You will need to put the following information into the notepad: echo off start "" steamcmd. This is important you have these settings correct to install it properly.
Now you can open the SteamCMD folder and let it create your server! You will see it working and then your server folder will have the Dedicated Server files ready. Open the TheForestDedicatedServer. This is needed one time to create the save folders and will make it easier. I would recommend you create a shortcut of your TheForestDedicatedServer. Now you can move the shortcut to your desktop or wherever you want it.
Now open the shortcut and it will launch the server. Let it sit for about 5 minutes so it creates all the save folders so its easy to modify when we close it. Ok, close the black windows and now we will goto the next setup to configure your configs and ports. You now will want to customize your settings and open the ports you specify in your Server. Let's start with the Server. The Forest Dedicated Server stores your Server. So you will need to enable Show hidden files in your view settings so you can see the hidden folder.
In the ds folder you will see your Server. This is good and means you have everything you ran the shortcut on the other page one time. So now you will want to open the Server. You would have to change it to something else if you are. Ignore that and leave the defaults if you just have this. The serverSteamAccount is recommend to create so it links you to the server.
Now you will want to open the ports you have 3 in config on your router and Windows Firewall if you have it enabled. This isn't easy to explain since there are thousands of routers out there. If you are more advanced, you can do the Advanced Options in your Windows Firewall and just open the ports to the IP Address if you know what your doing.
I usually recommand looking at what you currently have in DHCP and writing those down. You can use a high IP address like Or if you know how to exclude IP addresses you can do that and make it whatever. Note: It looks like it creates an entry in your Windows Firewall if you browse it. You can easily update your server files by running the. It will download any new updates and then you can just reopen the server. If they add new INIs you will want to watch the patch notes so you can add them, etc.
This guide is still being editted proofed. This was all typed out of my head with no pictures but should get you going. I might add pictures when I clean it up. Thanks for viewing this and I hope you have a server up and running! I would recommend the guide from SurvivalistGaming which I originally got started with. The ReDIM pst 1 part of the script sets how many pst-files you want to back up.
As this is an array, the counting starts at 0 and not 1. So ReDim pst 1 means you have 2 pst-files defined in the script to backup. If you only want to backup 1 pst-file, you must change this to ReDim pst 0. The location of each pst-file to back up. Define the location for each pst-file that you want to back up.
To figure out where your pst-files are located, you can follow the same instructions for manually backing up your pst-files. The backup location for your pst-files. Specify the folder to which you want to make your backups.
If this folder does not exist before running the script, the script tries to create it. This path may also be a network path, either specified as an UNC path or a mapped network drive. Any existing pst-files with the same name that exist in the folder will be overwritten.
Optionally configure: Delay to let Outlook close on its own. If Outlook is running, the script sends a Close command to Outlook and will wait for 30 seconds for Outlook to close on its own. Depending on your Outlook version and the amount of add-in that you have, the delay can be shortened or needs to be extended. This value is set in milliseconds. Whether or not to keep a history of your backups. To keep old backups, you can enable KeepHistory. The script will then create a subfolder with a date reference within the backup path.
Restart Outlook after completion. As you may be having Outlook open all the time, you can set the script to start Outlook again as soon as it is done. The core has been modified to always use the core options as a base, so that all custom configurations will be appended to the created configuration, effectively overriding the core options.
The problem with this is that changing any core option while the core is running will reset all duplicate configurations. Therefore only add configurations which will require a restart or do not exist in the core options, if you must use a custom uae. If there is an option missing that is a must have, please make an issue about it.
You have one bootable MB file called System. For that scenario, you should create a. The geometry will then be read from the file. Skip to content. Star Branches Tags. Could not load branches.
Could not load tags. Latest commit. Git stats 1, commits. Failed to load latest commit information. Updated and fixed PS3 build. Apr 17, Reorganize extra deps. Mar 4, Add VFS interface. Nov 9, Statusbar non-ascii limits. Nov 10, WHDLoad info launch improvements. Oct 11, Sep 1, Add ios targets and linux 32bit.
0コメント